Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Need help with folding a model? Ask here.
User avatar
Swapnil Das
Buddha
Posts: 1265
Joined: July 29th, 2013, 4:39 pm
Location: Dhaka, Bangladesh
Contact:

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by Swapnil Das »

Just my humble opinion would be, Double Tissue or Homemade tissue-foil.
We're all stories in the end.

My flickr Please visit and comment as much as you can!
saurabhsharma0130
Newbie
Posts: 13
Joined: May 14th, 2014, 8:18 pm

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by saurabhsharma0130 »

Could someone please post a picture of step 98? The description that the above person gave led to my paper tearing so I'm afraid I misunderstood.
My Flickr https://www.flickr.com/photos/126665475@N03/ 'In origami you dont add to the paper, you dont take away from it, you change it" Micheal Lafosse
Edg
Senior Member
Posts: 259
Joined: November 8th, 2012, 8:17 pm
Location: England

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by Edg »

What kind of paper are you using? You need to open the layers as much as possible and go steady!
saurabhsharma0130
Newbie
Posts: 13
Joined: May 14th, 2014, 8:18 pm

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by saurabhsharma0130 »

I was using glassine which in retrospect was not a good idea for the first try, I'll try it again today with 15inch rice paper
My Flickr https://www.flickr.com/photos/126665475@N03/ 'In origami you dont add to the paper, you dont take away from it, you change it" Micheal Lafosse
Xyresic
Newbie
Posts: 1
Joined: November 12th, 2016, 2:14 am

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by Xyresic »

I'm starting on Satoshi's models and I can't seem to figure out step 76 for this model. Can anybody help?
bethnor
Buddha
Posts: 1341
Joined: August 17th, 2006, 9:57 pm

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by bethnor »

step 76 from works of satoshi kamiya 2 or from the tanteidan convention?

in WOsK2--collapse the model on existing creases. as a rule of thumb, with complex collapses, perhaps a good universal tip is to make sure your mountains are mountain and your valleys are valleys. what is meant by that is, i think most folders just fold without paying too much attention. with complexes collapses, make sure you pay attention as to which is which--i.e., mountains will have the sheet on either side folding away from you, valley will have the paper folded towards you.

in the tanteidan magazine, step 76 is just a repeat of step 75--sink in and out. so i'll assume you're asking about the former.
pol origami
Newbie
Posts: 6
Joined: November 25th, 2016, 5:29 pm
Location: Ecuador
Contact:

Re: Satoshi Kamiya - Cyclommatus Metallifer(Stag Beetle)

Post by pol origami »

New magazine of "4 Esquinas" num 22
https://www.amazon.com/Revista-Latinoam ... 4+esquinas
Post Reply