Looking for: Butterfly with legs
Forum rules
READ: The Origami Forum Rules & Regulations
READ: The Origami Forum Rules & Regulations
- stevieboy1
- Super Member
- Posts: 133
- Joined: January 25th, 2009, 9:44 pm
- Location: Gravesend, Kent, UK
Looking for: Butterfly with legs
Hi all im really getting into folding butterflys but I only like the ones that have there legs etc. Ive made a few now. Just wonderd if anyone knows any good books etc or diagrams for any good ones with there legs?? i quite like the ones that M sirgo has done but dont know if they were ever diagramed etc?
Any help would be great.
Kind regards
Steve
Any help would be great.
Kind regards
Steve
-
- Junior Member
- Posts: 119
- Joined: December 18th, 2006, 7:32 pm
- stevieboy1
- Super Member
- Posts: 133
- Joined: January 25th, 2009, 9:44 pm
- Location: Gravesend, Kent, UK
If you can fold Lang's you could probably do Sirgo's Actias Dubernadii (a moth, but it's nice looking) from the CP. After you layout the 48X48 (or at least 24x24) grid, it's really just a matter of bringing out the right creases. After you collapse the base it's really easy to figure out how to fold the rest.
- stevieboy1
- Super Member
- Posts: 133
- Joined: January 25th, 2009, 9:44 pm
- Location: Gravesend, Kent, UK
You might like this Butterfly by Kamiya http://www.flickr.com/photos/cecilia13101/3276394560/
There is a diagram for a butterfly with legs here that's quite nice,
http://www.zingman.com/origami/ori_animals.html#lovebug
http://www.zingman.com/origami/ori_animals.html#lovebug
Live forever man...
- stevieboy1
- Super Member
- Posts: 133
- Joined: January 25th, 2009, 9:44 pm
- Location: Gravesend, Kent, UK
-
- Senior Member
- Posts: 356
- Joined: April 14th, 2008, 7:23 pm
- Location: St.-Petersburg, Russia
- Contact:
luna moth(Actias dubernardi)
designer -Jason Ku
cp - http://scripts.mit.edu/~jasonku/index.p ... =lunamoth2
designer -Jason Ku
cp - http://scripts.mit.edu/~jasonku/index.p ... =lunamoth2
- InsomniacFolder
- Senior Member
- Posts: 291
- Joined: January 12th, 2006, 3:26 pm
- Location: Maidenhead, UK
A picture of Engels Butterfly can be seen here: http://www.serve.com/hecht/origami/galpix/btrflye.jpgSushy wrote:Maybe you'd like to try Peter Engel's Butterfly from 'Origami from Angelfish to Zen'. It is pretty nice. Haven't found a pic though
Similar in structure to Lang's in Origami Zoo, Lang Boxpleats, Engel's is kite based.
"Had we but world enough and time..."
- stevieboy1
- Super Member
- Posts: 133
- Joined: January 25th, 2009, 9:44 pm
- Location: Gravesend, Kent, UK
Id love to fold Engel's Butterfly but i from what I can see it would be the only model id want to fold from Angelfish to Zen so I dont think I will be spending money out on it any time soon just for the one model lol Is it diagramed in any other book do anyone know?
I love all the ones that have been shown. I love the loona moth. I so wish I could fold cps. I keep trying but I just cant get it
Thanks for all your replys so far guys and girls!
Kind regards
Steve
I love all the ones that have been shown. I love the loona moth. I so wish I could fold cps. I keep trying but I just cant get it
Thanks for all your replys so far guys and girls!
Kind regards
Steve
Here's the basic steps for collapsing Sirgo's. It's really not super hard to collapse the crease pattern if you're diligent about creasing the grid and make the right creases.
1. Fold a 48x48 grid. Do this by first folding 3rds, then 6ths, etc. When you do the final division (the finest one, into 48ths) flip the paper over so that the creases end up like pleats going in both directions. This will help in collapsing later
2. Crease all the diagonal creases in the grid. Notice that when a vertical or horizontal crease hits a diagonal, it changes direction by 90 degrees. This is one of the big concepts behind box pleating.
3. Ever folded Shafer's two interlocking rings? This model is kind of like a big, complex two interlocking rings. The whole bottom half of the model can be collapsed by folding the valleys along the edge of the paper while rabbit-earing at the corners, then flipping over and doing the same on the back until you have two long points. These points are the tails.
4.The legs, antenna and upper wings are essentially repetitions of the above process, the same one used in Shafer's interlocking rings. The hardest part to collapse is probably where the upper wings meet the legs/antenna. You can pencil in the creases if you have to-- I don't think any purist mobs are in your area. The collapsed base looks like two long points and two short points, with a pack of eight small points for legs/antenna. You pull out some paper from the wing flaps and shape them to taste, then do the same with the legs.
good luck! If this didn't help maybe you can say where you're having a problem and I can give you some photos of my finished one if you want.
1. Fold a 48x48 grid. Do this by first folding 3rds, then 6ths, etc. When you do the final division (the finest one, into 48ths) flip the paper over so that the creases end up like pleats going in both directions. This will help in collapsing later
2. Crease all the diagonal creases in the grid. Notice that when a vertical or horizontal crease hits a diagonal, it changes direction by 90 degrees. This is one of the big concepts behind box pleating.
3. Ever folded Shafer's two interlocking rings? This model is kind of like a big, complex two interlocking rings. The whole bottom half of the model can be collapsed by folding the valleys along the edge of the paper while rabbit-earing at the corners, then flipping over and doing the same on the back until you have two long points. These points are the tails.
4.The legs, antenna and upper wings are essentially repetitions of the above process, the same one used in Shafer's interlocking rings. The hardest part to collapse is probably where the upper wings meet the legs/antenna. You can pencil in the creases if you have to-- I don't think any purist mobs are in your area. The collapsed base looks like two long points and two short points, with a pack of eight small points for legs/antenna. You pull out some paper from the wing flaps and shape them to taste, then do the same with the legs.
good luck! If this didn't help maybe you can say where you're having a problem and I can give you some photos of my finished one if you want.