Marking a grid

General discussion about Origami, Papers, Diagramming, ...
Post Reply
User avatar
OrigamiasaEnthusiast
Super Member
Posts: 241
Joined: May 9th, 2020, 3:53 pm
Location: [REDACTED]

Marking a grid

Post by OrigamiasaEnthusiast »

What are you supposed to do when Robert Lang asks you to mark the edges of a grid?
Sorry I don't have much experience folding, I am just starting back again but I enjoy it :oops: .
"Ethics are annoying, I avoid them on principle."-B. Katt
Can't delete account, so I'll open up a new one indefinitely in the future.
User avatar
OrigamiasaEnthusiast
Super Member
Posts: 241
Joined: May 9th, 2020, 3:53 pm
Location: [REDACTED]

Re: Marking a grid

Post by OrigamiasaEnthusiast »

Should I just put it on a sheet of A4, Mark the edges, and fold on the grid?
"Ethics are annoying, I avoid them on principle."-B. Katt
Can't delete account, so I'll open up a new one indefinitely in the future.
User avatar
origami_8
Administrator
Posts: 4371
Joined: November 8th, 2004, 12:02 am
Location: Austria
Contact:

Re: Marking a grid

Post by origami_8 »

Could you specify where exactly he wrote that? Out of context it can mean a lot of things.
User avatar
OrigamiasaEnthusiast
Super Member
Posts: 241
Joined: May 9th, 2020, 3:53 pm
Location: [REDACTED]

Re: Marking a grid

Post by OrigamiasaEnthusiast »

In the end of chapter 14, with the crease patterns.
"Ethics are annoying, I avoid them on principle."-B. Katt
Can't delete account, so I'll open up a new one indefinitely in the future.
User avatar
origami_8
Administrator
Posts: 4371
Joined: November 8th, 2004, 12:02 am
Location: Austria
Contact:

Re: Marking a grid

Post by origami_8 »

You are funny.
It is ODS2 page 686ff.

First of, non of the models there are suitable for A4 paper, you need something way bigger. For a first fold you shouldn't go below half a centimetre for a grid unit. Taking the very first model with a grid of 74x74 the initial sheet shouldn't be less than 30x30 cm and even that might be tricky for a beginner.

What Robert Lang suggests with marking the grid is not to fold the whole grid, but to actually make pencil marks along the border of the paper to mark the grid, and then only fold the grid lines needed. This can be be helpful for the collapse as you only have the necessary lines, but it can add a degree of complexity, given that folding accurately enough might not be so easy without prescoring the paper. Prescoring can be done with a ruler and a pointy blunt tool like an empty ballpoint pen or a nail doting tool, but it is very tedious. For ease of folding I would recommend to just fold the whole grid. (Robert prescores with a laser cutter.)
User avatar
Brimstone
Buddha
Posts: 1729
Joined: November 23rd, 2004, 3:59 am
Location: Colombia, South America
Contact:

Re: Marking a grid

Post by Brimstone »

You should be more specific with your inquiries.

I figured out what you were asking.

"Mark the edges of a 76×76 square grid" means that you don't extend the creases all across the paper, just mark the grid over the edges.
User avatar
OrigamiasaEnthusiast
Super Member
Posts: 241
Joined: May 9th, 2020, 3:53 pm
Location: [REDACTED]

Re: Marking a grid

Post by OrigamiasaEnthusiast »

Thank you. Sorry I didn't mention what book and page. So I should just fold it at the edges?
"Ethics are annoying, I avoid them on principle."-B. Katt
Can't delete account, so I'll open up a new one indefinitely in the future.
User avatar
Brimstone
Buddha
Posts: 1729
Joined: November 23rd, 2004, 3:59 am
Location: Colombia, South America
Contact:

Re: Marking a grid

Post by Brimstone »

OrigamiasaEnthusiast wrote:Thank you. Sorry I didn't mention what book and page. So I should just fold it at the edges?
Always mention the book and the step you're having trouble with (if it is a diagram).

And yes make pinches or small marks only at the edges so that your finished model doesn't end up with lots of unnecesary creases running all across it.
User avatar
OrigamiasaEnthusiast
Super Member
Posts: 241
Joined: May 9th, 2020, 3:53 pm
Location: [REDACTED]

Re: Marking a grid

Post by OrigamiasaEnthusiast »

Ah, I see. Thank you. I will try one of his models then :D Also, would It affect the model if I did the whole thing as a grid and folded not just at the edges? Also, marking is valley folds if I am correct, right?
"Ethics are annoying, I avoid them on principle."-B. Katt
Can't delete account, so I'll open up a new one indefinitely in the future.
NeverCeaseToCrease
Forum Sensei
Posts: 502
Joined: April 7th, 2017, 4:54 am
Location: USA

Re: Marking a grid

Post by NeverCeaseToCrease »

Usually mountain/valley doesn’t matter especially if it’s only marking the edges. Creasing all the all the way through would waste time and make the model less clean.
User avatar
OrigamiasaEnthusiast
Super Member
Posts: 241
Joined: May 9th, 2020, 3:53 pm
Location: [REDACTED]

Re: Marking a grid

Post by OrigamiasaEnthusiast »

Thank you!
"Ethics are annoying, I avoid them on principle."-B. Katt
Can't delete account, so I'll open up a new one indefinitely in the future.
Post Reply