Robert J. Lang - Tarantula (Insects II)

esato · Post by **esato** » December 21st, 2005, 9:01 am

I tried to fold Robert Lang's Tarantula.

Everything went fine upt to step 57 when what I got was different from the following picture. So I figured I must have done something wrong. I suspect I may have gone wrong doing the open sink at step 36.

IÂ´ve taken some pictures of the open sink. If any of you would be so kind as to check if thereÂ´s something wrong, I would apreciate it

Step 38:
[img]http://sv1.randomcrap.net/uploads/files/0/61037.jpg[/img]

View from the side:
[img]http://sv1.randomcrap.net/uploads/files/0/41297.jpg[/img]
[img]http://sv1.randomcrap.net/uploads/files/0/51197.jpg[/img]

thedeadsmellbad · December 21st, 2005, 10:40 pm

57 is a long way off from step 36 on this model, the sink looks fine, it may be further on in the sequence that something was overlooked. If you can't find it try the model again, because the instructions are pretty straight forward with little guess work. Just triple check as you progress through the steps.

esato · Post by **esato** » December 22nd, 2005, 12:43 pm

thedeadsmellbad wrote:57 is a long way off from step 36 on this model, the sink looks fine, it may be further on in the sequence that something was overlooked. If you can't find it try the model again, because the instructions are pretty straight forward with little guess work. Just triple check as you progress through the steps.

Actually, this is not my first try !!! IÂ´ve actually memorized all steps up to step 57...

I think the problem might lie at 36 because thereÂ´s another open-sink at step 35 and the open-sink that must be done at step 36 is done over the previous open-sink.

At step 57, when I "fold one layer to the right" I get something completely different from step 58. However, apparently up to that step everything looks the same as the pictures.

esato · Post by **esato** » December 22nd, 2005, 3:08 pm

This is what I have at step 53.

[img]http://sv1.randomcrap.net/uploads/files/0/tarantula1.jpg[/img]

Later, at step 57, if "Fold one layer to the right" this is what I get:

[img]http://sv1.randomcrap.net/uploads/files/0/tarantula2.jpg[/img]

I can't fold one layer to the right, as that layer is stuck...

esato · Post by **esato** » December 25th, 2005, 10:49 pm

CanÂ´t anyone help ?

If anyone ever folds this model, I beg them to take pictures of steps 38 and 58

esato · Post by **esato** » January 17th, 2006, 9:39 pm

I found out what I was doing wrong. I folded a closed sink instead of an open sink at step 36.

EuanBingham · Post by **EuanBingham** » January 17th, 2006, 9:50 pm

What kind of paper is that you're using?

Euan

esato · Post by **esato** » January 17th, 2006, 10:31 pm

EuanBingham wrote:What kind of paper is that you're using?

Euan

Parchment paper !

EuanBingham · Post by **EuanBingham** » January 18th, 2006, 7:15 pm

Hmm.. wierd, looks too thin to be parchment paper.

Euan

Darksoul · Post by **Darksoul** » July 12th, 2006, 7:46 pm

This a reply that's way out date, but just in case it helps, the problem is when you make the sink at step 35 you need to open sink the hole flap that paper is trapped because you closed sink the very point, to solve this simply go to the view on step 53 and grab the nearest layer from the sides on the top and gently pull the paper out to the sides to release it, you know what I mean after that everything fits.

naabox · Post by **naabox** » September 12th, 2007, 7:48 am

I folded a new diablo tarantula by Robert Lang

naabox

esato · Post by **esato** » September 12th, 2007, 11:23 pm

naabox:

What paper size did you use?

naabox · Post by **naabox** » September 13th, 2007, 9:40 am

I used paper 40x40 to make this model.

Oruhito · Post by **Oruhito** » September 14th, 2007, 1:47 pm

Great Job looks pretty good! How did you collapse the middle? Any photos? I really want to try this model!