Help folding Roman Diaz Unicorn
Forum rules
READ: The Origami Forum Rules & Regulations
READ: The Origami Forum Rules & Regulations
Help folding Roman Diaz Unicorn
Hello everybody,
I was wondering if anyone can give me a help in folding Diaz' Unicorn. I am in troubles with step number 34, which is not really clear to me. It says "Wrap the layer behind to the front", but actually I don't understand if it's a kind of sink fold or else.
Browsing the later steps, it would be great if you could also give a clue about steps 38-40 that look quite complicated.
Thanks a lot for helping!
Chrom_
I was wondering if anyone can give me a help in folding Diaz' Unicorn. I am in troubles with step number 34, which is not really clear to me. It says "Wrap the layer behind to the front", but actually I don't understand if it's a kind of sink fold or else.
Browsing the later steps, it would be great if you could also give a clue about steps 38-40 that look quite complicated.
Thanks a lot for helping!
Chrom_
It's not a sink, the fold in 34 will form part of the mane, if you look at 36 it seems that nothing had happened, but really the flap that in 34 is trapped is now free.
38 - 40 it's a little tricky, the only advice I can give you is to mark really well the folds shown in 39, pivoting around the point indicated everything should go at its place.
38 - 40 it's a little tricky, the only advice I can give you is to mark really well the folds shown in 39, pivoting around the point indicated everything should go at its place.
-
- Newbie
- Posts: 11
- Joined: March 4th, 2007, 8:53 pm
Step 44 is something like a "unsink", you have to separate the upper layer from the under one following the signed folds, like "blowing up", the model is now no more flat, probably in step 45 there's an error on the colour of the layer, but if you look closely at the shape of the different layers in step 46 it should be clear what happens.
Then the flap "blown" on step 44 comes back at his place.
You must consider that the point marked "x" in step 43 is inside and in the end at step 47 outside.
Then the flap "blown" on step 44 comes back at his place.
You must consider that the point marked "x" in step 43 is inside and in the end at step 47 outside.
-
- Newbie
- Posts: 11
- Joined: March 4th, 2007, 8:53 pm
-
- Newbie
- Posts: 4
- Joined: January 17th, 2011, 10:36 pm
Diaz Unicorn step 44-47 the mane
Hi all, could someone upload a picture or email me a picture of this process as it's causing my hair to go grey!!
When will enough be enough?
-
- Newbie
- Posts: 11
- Joined: March 4th, 2007, 8:53 pm
-
- Newbie
- Posts: 4
- Joined: January 17th, 2011, 10:36 pm
-
- Newbie
- Posts: 2
- Joined: January 31st, 2011, 9:34 am
I'm stuck at level 43 too!!
Someone just told me I should use wet fold which I did not... I think it might be the reason why I'm stuck here. Though I have not tried it yet.
Anyone can tell me from the link below... which opening should I do the sink? 1st opening layer or 2nd opening layer?
http://www.youtube.com/watch?v=KmpmQcEnaus
Someone just told me I should use wet fold which I did not... I think it might be the reason why I'm stuck here. Though I have not tried it yet.
Anyone can tell me from the link below... which opening should I do the sink? 1st opening layer or 2nd opening layer?
http://www.youtube.com/watch?v=KmpmQcEnaus
I am folding Roman Diaz unicorn origami, stuck with step 43! Please help by visit link
http://www.youtube.com/watch?v=KmpmQcEnaus
http://www.youtube.com/watch?v=KmpmQcEnaus
-
- Newbie
- Posts: 2
- Joined: January 31st, 2011, 9:34 am
I think I got it@@ YES! I'm so happy now!
I am folding Roman Diaz unicorn origami, stuck with step 43! Please help by visit link
http://www.youtube.com/watch?v=KmpmQcEnaus
http://www.youtube.com/watch?v=KmpmQcEnaus
-
- Newbie
- Posts: 4
- Joined: January 17th, 2011, 10:36 pm
-
- Newbie
- Posts: 4
- Joined: January 17th, 2011, 10:36 pm