Eric Joisel - Dwarf (CP)

Origami middle east! · January 22nd, 2011, 4:39 pm

I fixed the problem of the dwarf looking to human.
p.s; the paper I used was sandwich paper: I glued thin carton paper on aluminum, then wet folded the model, and finally put the model in the freezer to make the model as strong as stone. I finally finished by spraying the model with varnish.
Once I have proper sunlight again, I will take better pictures.

RicardoMontecinos · January 27th, 2011, 2:35 am

Dwarf of Joisel and finally completing the orchestra,

The Average Folder · January 27th, 2011, 4:25 am

aren't you going to shape the rest of those dwarves?

Looks like tedious work. I wish you luck

RicardoMontecinos · January 27th, 2011, 4:42 pm

Tedious work ????????
I said ... that I am finally finished all the band
cost me much time to make their clothes
and deduct the instruments, I did
the greatest tastes
I think my English is not very good

The Average Folder · January 27th, 2011, 5:18 pm

Yes, but it seems to me that you have one finished piece and a lot of bases from what it looks like in the picture no?

RicardoMontecinos · January 27th, 2011, 10:18 pm

this photo is old, mid-of December friend I need only two models to complete the band jaz upload the full band soon.

The Average Folder · January 28th, 2011, 2:51 am

Cool nice, can't wait to see it.

I dont have the patience for that kind of thing

1folder · Post by **1folder** » January 30th, 2011, 11:39 pm

i've tryed this fold too, and i have to admit that its really funny to crease. thats my try

Pop pop · Post by **Pop pop** » February 6th, 2011, 3:04 am

cranemaster366 wrote:Could somebody PLEASE make a cleaner saxaphone cp. I can't make much of it. The accordian is a bit tricky too, but it is less troubling to figure out.

the bottom of the cp were it says collage glue it up above were it says collage thats were you are going to do all the 2 1/2 units and 3 in the middle
here for bigger image http://forums.ngemu.com/open-discussion ... assed.html
hope this help

Pop pop · Post by **Pop pop** » February 27th, 2011, 5:11 am

can anyone help me stand up mr.joisel dwarf because i cant

The Average Folder · February 27th, 2011, 7:02 pm

If you are using foil paper, it should be pretty easy. Just organize the legs perpendicular to each other, and make his weight go on the front forward pointing foot, and balance him using the other. The feet should look like this: _|. If you are using normal paper, use MC to do the same thing.

HankSimon · Post by **HankSimon** » February 27th, 2011, 7:59 pm

When you look at the pictures of the various dwarves, then you can see what Average Folder is saying.

If you can't get your model to stand, after following his suggestion, then post some pictures of your model from various angles...

- Hank Simon

Pop pop · Post by **Pop pop** » February 27th, 2011, 9:12 pm

ok i post it on here

maddoghoek100 · Post by **maddoghoek100** » February 28th, 2011, 9:18 am

What works for me is to put a little crimp in the foot right next to the ankle, if you just press down till the fold of the foot pops inward toward the ground the entire foot will splay outward and make a very stable base. Below is a picture of some i did recently, hope it helps.

gonzalospinettta · February 28th, 2011, 11:03 pm

My last dwarf

http://www.flickr.com/photos/gonzalobe/4799372294/

I love it