Satoshi Kamiya - Ryu Zin (CP)

Kafar · Post by **Kafar** » November 18th, 2009, 9:21 pm

yes there is 0.5 unit cause just from te edge there is 1,5 unit for the spine scales

and then 4,5 units for scales, 1 unit for the belly, 4,5 units for scales again, and than the rest of the boxpleating

angrydemon · Post by **angrydemon** » November 19th, 2009, 5:33 pm

This is what I have so far...

I won't be around for the next few days, so I might as well post this so nobody thinks I'm dead.

artur biernacki · Post by **artur biernacki** » November 19th, 2009, 9:55 pm

I folded of Ryu zin 2,1 By Kamiya Satoshi.

Artur
http://www.flickr.com/photos/12569445@N02/

insaneorigami · Post by **insaneorigami** » November 19th, 2009, 10:27 pm

*sigh*. Simply amazing, Artur...

But where is the tongue?

artur biernacki · November 19th, 2009, 10:38 pm

Thanks. Ryu zin 2,1 don't have tongue.
See this:
http://img682.imageshack.us/i/ryuzin.jpg/
and this:
http://www.folders.jp/g/2000/0015.html
Artur
http://www.flickr.com/photos/12569445@N02/

insaneorigami · Post by **insaneorigami** » November 19th, 2009, 10:44 pm

Hmmm, then what did you do with the flap that is between the upper and lower jaws? I always used it as a tongue, but... ...hmmm...

EDIT: I finished my last four sheets of tissue foil.. ..hopefully, I will have each of them trimmed, squared, and into a 32/32 grid tonight... then, my square will be done!

Froy · Post by **Froy** » November 20th, 2009, 1:37 am

insaneorigami wrote:Hmmm, then what did you do with the flap that is between the upper and lower jaws? I always used it as a tongue, but... ...hmmm...

That flap is used to fold the teeth in upper jaw. If you use this flap to fold the tonge you won't have any point to fold the teeth. That's why I used 3.5 head in my 2.1 ryuzin.

gonzalospinettta · November 20th, 2009, 12:34 pm

I don´t understand . look this page
viewtopic.php?t=558&postdays=0&postorder=asc&start=555

Ryu jin 2.1 have a tongue

Adam · Post by **Adam** » November 20th, 2009, 12:43 pm

Like Froy said, he used the head of Ryu Jin 3.5 but the body of Ryu Jin 2.1.
It's kind of a combination of both models, so technically speaking it's not really Ryu Jin 2.1

gonzalospinettta · November 20th, 2009, 12:57 pm

ok, but I have a diagram of ryu jin head , the author it does by cp 2.1 and in the diagram appears with tongue

Kafar · Post by **Kafar** » November 20th, 2009, 1:15 pm

first of all, it isn't made by Satoshi, so it's not 100% what you will get after collapsing, 2nd if you will fold tongue, you want have upper teeth, or if you fold with tongue and upper teeth you won't have nose, it's simple, there are not enough flaps in 2,1 version, look at 3,5 cp of the head and you will get answer why is that imposible to have everything like 3,5 in 2,1

insaneorigami · Post by **insaneorigami** » November 20th, 2009, 9:09 pm

Ah, thanks for clearing that up, Froy and Kafar

.
I finally finished my 96/96 grid, 54 inch sheet of paper!

insaneorigami · Post by **insaneorigami** » November 21st, 2009, 9:40 pm

I have a question:
Do the two sections of scales for Ryu Zin 3,5 get joined before you start making them, or after?
I was looking at Kafar's picture:http://www.flickr.com/photos/magik9/4104849475/
And it looked like the scales were already overlapped..

For 2.1, I folded the all the scales, and at the end, unfolded the ones closest to the joining area, and attached them. This, however, would be much harder with 3,5, as there are 5 rows of scales, rather than 3...

Kafar · Post by **Kafar** » November 21st, 2009, 10:19 pm

No, it only looks like that

insaneorigami · Post by **insaneorigami** » November 21st, 2009, 10:58 pm

Ah, thanks

. Scales on the legs not coming along well at all.... I did half of one leg, but the other half are just KILLING me!. grrrrr.....