Step 26 of Nguyen Hung Coung Butterfly?

Need help with folding a model? Ask here.

Step 26 of Nguyen Hung Coung Butterfly?

Postby Wuggums47 » May 4th, 2014, 12:55 am

In the book Vog2 page 124, step 26 it says I am supposed to push the corner upwards. the picture shows three arrows, 2 of which are white, and one of which is black. I think this means closed sink, but I'm not sure. The picture also shows a mountain fold line, and if you did a closed sink, it would be a valley fold there. What am I supposed to do?
Be who you are, do things because you want to do them, and stop caring what others think. Then you'll be happy.
Wuggums47
Junior Member
 
Posts: 58
Joined: March 28th, 2014, 9:53 pm

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Mir Numaan » May 4th, 2014, 3:43 am

that step is quite easy, all you have to do is closed un-sink the layer up. If it was not clear, i can make a photo diagram. Also, the mountain fold in the diagram is wrong, its a valley fold, IMO.
Mir Numaan
Buddha
 
Posts: 1204
Joined: April 18th, 2013, 3:37 pm
Location: europa

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Wuggums47 » May 4th, 2014, 4:32 am

Thank you so much for your reply, so soon after I asked too. This solves everything, thanks for your offer to make a diagram, but I think I know what to do.
Be who you are, do things because you want to do them, and stop caring what others think. Then you'll be happy.
Wuggums47
Junior Member
 
Posts: 58
Joined: March 28th, 2014, 9:53 pm

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Wuggums47 » May 4th, 2014, 6:25 am

I need help again, I'm at step 69-70 and I don't understand them one bit. When I get to step 70 there is no corner to push in. Did I do step 66 wrong, if so how do I do that?
Be who you are, do things because you want to do them, and stop caring what others think. Then you'll be happy.
Wuggums47
Junior Member
 
Posts: 58
Joined: March 28th, 2014, 9:53 pm

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Edg » May 4th, 2014, 8:00 am

If I remember correctly, there's no corner as such, the flap should be curved towards you where the valley fold is shown (step 70) You need to push that in so it curves away, to allow that valley fold. I always seem to struggle with intermediate steps like this! I just messed around until it looked right ( the colour change is only on the front face of the flap) Hope this helps/makes sense! :)
Edg
Senior Member
 
Posts: 259
Joined: November 8th, 2012, 8:17 pm
Location: England

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Mir Numaan » May 4th, 2014, 8:20 am

i explained it roughly
http://imgur.com/a/cHHS6
sorry if it doesn't help :(

you would have done step 66 incorrectly.there should be a corner which needs to be pushed in slightly. Then hold 2 layers on the left side and the one single layer (3rd layer) on the right side and make a series of outside reverse folds.
Mir Numaan
Buddha
 
Posts: 1204
Joined: April 18th, 2013, 3:37 pm
Location: europa

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Wuggums47 » May 4th, 2014, 3:34 pm

Are those steps 69-70, or some different steps? Your paper doesn't look like mine.
Be who you are, do things because you want to do them, and stop caring what others think. Then you'll be happy.
Wuggums47
Junior Member
 
Posts: 58
Joined: March 28th, 2014, 9:53 pm

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Wuggums47 » May 4th, 2014, 3:43 pm

Never mind, figured it out, thanks Mir, thanks Edg!
Hopefully this is the last time I need to ask about this model.
Be who you are, do things because you want to do them, and stop caring what others think. Then you'll be happy.
Wuggums47
Junior Member
 
Posts: 58
Joined: March 28th, 2014, 9:53 pm

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Wuggums47 » May 4th, 2014, 4:20 pm

I can't explain how this is possible, but despite doing it already, I forgot how to do step 66 again. Maybe I'm not meant to finish this model on the first try, it's looking pretty mangled...
Be who you are, do things because you want to do them, and stop caring what others think. Then you'll be happy.
Wuggums47
Junior Member
 
Posts: 58
Joined: March 28th, 2014, 9:53 pm

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby Edg » May 5th, 2014, 5:39 pm

Keep going! Learn what you can of the model this time, then you'll get a better result next time. That's how I go about things anyway. Then again, sometimes a good old rage quit is just as helpful :wink: Its a tricky model,this one, I think :)
Edg
Senior Member
 
Posts: 259
Joined: November 8th, 2012, 8:17 pm
Location: England

Re: Step 26 of Nguyen Hung Coung Butterfly?

Postby sebastien75 » July 28th, 2016, 4:15 pm

hello everybody
i have an issue with the steps 75 to 77
i open the layer step 75, fold the close sink after that i close the layer step76 allong the valley fold line.
it s easy ... but when i look at the step 77 the externa edge of this flap is not straight as it was on step 75
i don't understand how it is possible to obtain a split edge whith the valley fold of a straight line
thank you for your help
sebastien75
Newbie
 
Posts: 4
Joined: July 28th, 2016, 4:05 pm


Return to Diagrams & Crease Patterns

Who is online

Users browsing this forum: No registered users and 5 guests