Satoshi Kamiya - Ryu Zin (CP)

Need help with folding a model? Ask here.

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby SeekerKuba » November 27th, 2018, 12:55 am

Those 4 sections are 22.5...
SeekerKuba
Newbie
 
Posts: 6
Joined: April 15th, 2018, 11:23 am

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Baltorigamist » November 28th, 2018, 3:36 am

Merman -> They're based on 22.5--otherwise the axial creases on either side wouldn't line up.
After the fall...we rise.

My Flickr DeviantArt
Baltorigamist
Moderator
 
Posts: 2073
Joined: December 25th, 2011, 7:15 pm
Location: Inside my twisted little mind....

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby merman » November 28th, 2018, 6:23 pm

Thx. Then the cp Kamiya created has angles that are a bit off in the head section. The leg sections seem ok.
User avatar
merman
Senior Member
 
Posts: 302
Joined: February 23rd, 2008, 3:02 pm
Location: Amsterdam

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Tahaorigami » December 4th, 2018, 7:39 pm

Image

Image

After 3 months! Working on the lower scales right now. Paper used was 2m x 2m white tracing paper.
User avatar
Tahaorigami
Senior Member
 
Posts: 283
Joined: December 28th, 2012, 8:37 pm
Location: Pakistan

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Tahaorigami » December 19th, 2018, 12:25 pm

Done with the Ryujin 3.5
Tracing paper 2m x 2m
Time taken: 4 months

Image

Image

Image

Image

Image

Image

If you plan to fold it, make sure you have lots of patience and don't usually get frustrated easily, or else you'll end up screwing up the whole thing. If you get stuck at a molecule, take a break! (im serious)
Later, test fold the difficult molecule on a separate piece of paper to prevent crumpling on the original. That's how you will end up with a neat fold and your hard work will pay off!
User avatar
Tahaorigami
Senior Member
 
Posts: 283
Joined: December 28th, 2012, 8:37 pm
Location: Pakistan

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Diego030505 » January 12th, 2019, 7:27 pm

Hello, could someone help me I will start folding the ryujin 2.1 and also I will do the 3.5 (in the future a little distant) and I would like you to help me with tips and crease patterns of parts of the ryuijin (both 2.1 and 3.5), to do test folds, I would like that I stay as clean as possible and that's why I think I should practice before. I also wanted to know if the scales of ryujin 2.1 can be shaped because it would give a good result to the dragon. Thanks in advance.
User avatar
Diego030505
Newbie
 
Posts: 3
Joined: January 12th, 2019, 6:58 pm

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Diego030505 » January 13th, 2019, 4:11 am

Hello, I will start to double the ryujin 2.1 and also the 3.5 (in the near future), could you help me with tips and send parts of the cp of both versions to test folds, especially on the leg because I read that is so difficult? (the majority who were in the forum disappeared), because I think that to achieve a very clean finish I must practice. Thanks in advance :D .

PSDT: Is there any way to shape the scales of ryujin 2.1?
User avatar
Diego030505
Newbie
 
Posts: 3
Joined: January 12th, 2019, 6:58 pm

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Tahaorigami » January 14th, 2019, 4:11 pm

Diego030505 wrote:Hello, could someone help me I will start folding the ryujin 2.1 and also I will do the 3.5 (in the future a little distant) and I would like you to help me with tips and crease patterns of parts of the ryuijin (both 2.1 and 3.5), to do test folds, I would like that I stay as clean as possible and that's why I think I should practice before. I also wanted to know if the scales of ryujin 2.1 can be shaped because it would give a good result to the dragon. Thanks in advance.


The scales of Ryujin 2.1 can't be shaped due to their smaller size. Even if you use a larger sheet, they won't be that impressive due to lack of dorsal spines.
Just test fold the head, legs, tail, scales and neck twist for the 2.1 and later, the 3.5!
User avatar
Tahaorigami
Senior Member
 
Posts: 283
Joined: December 28th, 2012, 8:37 pm
Location: Pakistan

Re: Satoshi Kamiya - Ryu Zin (CP)

Postby Diego030505 » January 20th, 2019, 7:06 pm

But I would like to know where to find the CP by parts and if there is a cp for the ryujin 3.1, and if not, how they do it to do it. Thanks in advance.
User avatar
Diego030505
Newbie
 
Posts: 3
Joined: January 12th, 2019, 6:58 pm

Previous

Return to Diagrams & Crease Patterns

Who is online

Users browsing this forum: Exabot [Bot] and 3 guests