Page 1 of 2

Alduin by Satoshi Kamiya

PostPosted: September 21st, 2016, 9:51 pm
by ToHS Origami
Anyone have the reference point for this CP? Image

Re: Alduin by Satoshi Kamiya

PostPosted: September 22nd, 2016, 5:27 am
by ShuaiJanaiDesu
I think the top edge ref points are: 1:√2:√2:2:2

or the main diagonal is: 1:√2:1:√2:2:1

(which ever is easier to use/fold from, I guess)

Re: Alduin by Satoshi Kamiya

PostPosted: September 22nd, 2016, 4:45 pm
by Mir Numaan
Image
Image
The collapsing is very easy, but the model is like 100 steps away from the finished product. I personally couldn't even figure out the head

Re: Alduin by Satoshi Kamiya

PostPosted: September 22nd, 2016, 6:18 pm
by ToHS Origami
I tried out 1/8th, but the leg / back spine area doesn't collapse perfectly.

Re: Alduin by Satoshi Kamiya

PostPosted: September 23rd, 2016, 11:53 pm
by ShuaiJanaiDesu
ShuaiJanaiDesu wrote:I think the top edge ref points are: 1:√2:√2:2:2

or the main diagonal is: 1:√2:1:√2:2:1

One way of folding this is:

Image

Fold the 22.5 deg.(black lines) then mark 50% above the end of that fold and fold from that mark to the lower corner. The intersection between that and the main diagonal will give you a key ref. point. (red lines)
(The intersection marks between 2+2√2 and 3)

From there, the second picture shows how to further fold into the crease pattern. (First, fold the black then the blue)

(Personally I don't like having to fold thirds so I might look for other ways of folding the ref. point. Although, thirds isn't too bad, I guess)

Re: Alduin by Satoshi Kamiya

PostPosted: September 24th, 2016, 12:13 am
by ToHS Origami
Ah thank you! Going to test this one out.

Re: Alduin by Satoshi Kamiya

PostPosted: September 24th, 2016, 7:53 am
by alorion
ShuaiJanaiDesu wrote:(Personally I don't like having to fold thirds so I might look for other ways of folding the ref. point. Although, thirds isn't too bad, I guess)

Image

Re: Alduin by Satoshi Kamiya

PostPosted: September 25th, 2016, 5:25 pm
by Mir Numaan
1/8 is incorrect? I actually found it here: http://tieba.baidu.com/p/4764980435

Re: Alduin by Satoshi Kamiya

PostPosted: September 26th, 2016, 1:46 am
by alorion
Mir Numaan wrote:1/8 is incorrect? I actually found it here: http://tieba.baidu.com/p/4764980435

ShuaiJanaiDesu rights - side of the square is: 5+2*sqrt(2)
Green - correct, orange - incorrect:
Image

Re: Alduin by Satoshi Kamiya

PostPosted: September 26th, 2016, 8:05 am
by Mir Numaan
hmm that explains, thanks for clarifying. I am still stuck on figuring out the head, i will probably just wait for diagrams if they ever get published

Re: Alduin by Satoshi Kamiya

PostPosted: September 26th, 2016, 6:09 pm
by ToHS Origami
I personally find the head easy compare to the wings. Wish someone can post a clear picture of the back side of the wings.

Re: Alduin by Satoshi Kamiya

PostPosted: February 13th, 2017, 2:52 pm
by Gabrielhk97
I was able to fold the head and collapse the model, the problem is how to shape the wings??? About the back, i think that the extra flap next to the tail in the belly section is used to create the spikes in the back, by simply reversing the flap and then pulling out. Maybe i can post a photo later on the model.

Re: Alduin by Satoshi Kamiya

PostPosted: March 16th, 2017, 8:45 am
by ToHS Origami
Wondering if there is an easier way to fold the reference point? Using a large sheet of paper makes it almost impossible to precrease it.

Re: Alduin by Satoshi Kamiya

PostPosted: April 1st, 2017, 9:27 am
by PleatBox
The best you can do is plot the reference points using a ruler, but since the reference points are often irrational numbers, you technically cannot get it perfect all the time. You can use reference finder but that requires folding sequences to get to the reference points.

Re: Alduin by Satoshi Kamiya

PostPosted: April 8th, 2017, 8:55 pm
by Gabrielhk97
I folded it, but the head shape ended up different and i managed to fold only 2 spikes in the back instead of 3.
Apparently, the forum says that i can't have a image larger than 640 pixels wide as an img BBcode, so i posted a link:
http://imgur.com/Olax2Ia