Satoshi Kamiya - Ryu Zin (CP)
Forum rules
READ: The Origami Forum Rules & Regulations
READ: The Origami Forum Rules & Regulations
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
Alright, Thanks.
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
Miscounted the amount of units for the scale precreasing. Had to start again. That base is in the trash.
Making new base ATM.
Current progress:
Ryujin 2.1 in progress by Swapnil Das, on Flickr
Currently doing "Short" Transition's. Looking pretty good!
Making new base ATM.
Current progress:
Ryujin 2.1 in progress by Swapnil Das, on Flickr
Currently doing "Short" Transition's. Looking pretty good!
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
Ryujin 2.1 in progress by Swapnil Das, on Flickr
Ryujin Road of Scales by Swapnil Das, on Flickr
Ryujin Scales Close-up by Swapnil Das, on Flickr
Ryujin Road of Scales by Swapnil Das, on Flickr
Ryujin Scales Close-up by Swapnil Das, on Flickr
- origamifan11
- Super Member
- Posts: 136
- Joined: February 6th, 2013, 9:40 am
- Location: Somewhere between the 9th and 10th dimension.
Re: Satoshi Kamiya - Ryu Zin (CP)
Looks good! My progress - I have finished making the scales on the upper half and have collapsed all of it expect for the head, and a question - Do I neck-twist before or after collapsing the head base?
Re: Satoshi Kamiya - Ryu Zin (CP)
I'd do it after, makes it a lot easier to handle.
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
Thanks Yeah, I'd suggest the neck twist after you collapse the head base.origamifan11 wrote:Looks good! My progress - I have finished making the scales on the upper half and have collapsed all of it expect for the head, and a question - Do I neck-twist before or after collapsing the head base?
Re: Satoshi Kamiya - Ryu Zin (CP)
I have just started my 4th attempt at the Ryujin 3.5. I am using Kraft paper with a weight of 55gsm and 120x120cm in size, and in two separate parts. Is that good?
Check out my flickr page
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
120 is too small for a good 3.5... Try to find a bigger paper as shoulder scales get SUPER small while folding. You must remember that 96 is not a small grid. The bigger the grid, the smaller the lines.
Re: Satoshi Kamiya - Ryu Zin (CP)
Well I could have gone as high as 180x180cm but my desk isn't big enough.
Check out my flickr page
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
Hmm.. I usually fold big paper's in the floor. As my desk isn't big enough, either.
Re: Satoshi Kamiya - Ryu Zin (CP)
Here is a picture of my progress on the bottom half. I have gone straight into the scale transitions.
Check out my flickr page
- origamifan11
- Super Member
- Posts: 136
- Joined: February 6th, 2013, 9:40 am
- Location: Somewhere between the 9th and 10th dimension.
Re: Satoshi Kamiya - Ryu Zin (CP)
Looks good, but I would suggest buying WOSCO before attempting the 3.5. It has the official cp (your's isn't) and some advice on flap arrangement of the head, how to make the necktwist, etc. Also if your desk isn't big enough to fit your paper on (mine isn't either), fold on a table (I use our dining table and move when it is going to be used).
Re: Satoshi Kamiya - Ryu Zin (CP)
What is WOSCO? I am already halfway through the scales of the bottom half of the model. And I used a mountain-valley crease pattern diagram for the legs. The scales look very clean, but I think I am overusing the binder clips a bit.
Check out my flickr page
- Swapnil Das
- Buddha
- Posts: 1265
- Joined: July 29th, 2013, 4:39 pm
- Location: Dhaka, Bangladesh
- Contact:
Re: Satoshi Kamiya - Ryu Zin (CP)
Oh, man, you just ruined your ryujin. The cp you're using is the FAKE CP For the 3.5. Buy World of Super COmplex Origami by Satohi Kamiya. It has the original CP which Kamiya used for 3.5. The one in the internet is just a fake CP.
Re: Satoshi Kamiya - Ryu Zin (CP)
I just found the book on scribd.com but it's all in japanese. But all the stuff on the Ryujin looks very useful. By the way I did use the updated crease pattern for the transitions from leg to leg scales. The rest of the updated crease pattern included added detailing to the scales and a different look on the end of the tail. Everything else in the crease pattern seems the same. (except it is now a mirror image of the 'fake' crease pattern.
Check out my flickr page